Search Results for ‘bolts’

The silver button inside the car that releases the E-brake keeps popping out of the handle. So the E-brake won't engage anymore. I have had this problem for a while now and it looks like the thread inside the plastic button has been rubbed out completely so it can't skrew on the E-brake cable...

Hello my name is Heyshar. I've been a member since last year. I didnt know how this worked so I have never write anything over here. Now I have a problem and I dont know if this is the right forum. But my car is a 08 Mitsubishi Eclipse gt 3.8 M/T. Im having problems trying to find the flywheel...

Trying to remove wheel hub and bearing to replace got all bolts out but hub is basically stuck I’ve tried penetrating oil and hammering to no luck what can I do to remove this without getting a shop to do it? Should I just keep hammering it it hasn’t even broke a crack in between the two pieces...

Flywheel Issues 2006 GT v6 MT Hi, I have a 2006 Eclipse GT 3.8L Manual Trans and have recently pulled the flywheel and was going to replace it when i noticed there were no shims. It had been burning up starters and this may be the reason from what i've read. One guy listed part #MD365781 and...

Greetings all new here - just bought a 2006 GT/manual. Absolutely love it! It came with a new driver's side door latch - owner said it needed it for the power lock to work. Is there a good write-up here for ripping into that door panel? Lots of bolts! LOL... I've been searching for a...

This post is old. Find the updated one at the link below https://www.club4g.org/board/automotive-sale-wanted/120507-4g69-build-kits-pistons-rods-bearings-studs.html#post1915771 Hey guys, So first up in my series of kits I'll be selling, I have 4G69 engine build kits! These will be to support...

2006 Eclipse GT 3.8L V6 MT So, I have an intake and exhaust done and originally I was gonna stick to bolt-ons and leave her alone but... then a brand new turbo was gifted to me from a friend who had no use for it. So... now here we are. I have started looking into the measures I need to take...

Hello I have a problem with my 6g75. 3 times I faced problems with bearings. I`ve read that the problem is related with center main bearing bolts. Someone can help me indicating which bolts I have to buy and from which store? Best regards, Mauro

I'm attempting to do a full coolant flush on my 2008 Eclipse GT tomorrow and as the manual states you don't just drain the coolant from the radiator. There are actually two bolts on the engine block, both front and back, to drain all the fluid out completely. My question is, is it necessary to...

Hey guys, I'm trying to install a strut brace however for some reason it seems like there's bolts that are doing nothing in the way of the boot for the brace. I'm new to this, so it may be something obvious I'm unaware of. But does anybody know what these bolts are/if I can remove them...

So I just received the my new RRE header for my 2.4 Eclipse and I was hoping to replace the rusted bolts studs coming out of the cylinder head that you slide the top 6 holes in the exhaust manifold onto...... now I’m not sure how difficult that would be while having it in the car because I...

Might anyone be interested in a used set of Brembo Evo X calipers? Some of the clear coat is coming off but besides that that are fine. Ill replace the seals and rebuild the calipers before shipping. Im trying to see all who might be interested. I would be willing to ship for $750 This is a...

Hey everyone, I'm a bit new to this forum. First off, I have a 2007 GS with a 4g69. Its got about 98k miles on it, and has a pretty bad exhaust leak from the front pipe. Cracked at the middle of the "Y' and has two holes right next to em as well. Not to mention, signs of leaking gaskets at just...

Didn't see a step by step so I thought I'd help out. I did not disconnect exhaust. But you may have to depending on your setup. Step 1 is get a jack with a piece of wood on it and support the transmission. Step 2 is remove the rear two bolts on the centermember. Step 3 is remove the...

After reading the manual and what I could find here, I've come to the conclusion that either i'm retarded or i'm missing something. But in the process I found it a whole lot easier to just remove the 6 bolts holding it down, push it up as far as it goes. than you can access the lower bolt on the...

I have a 2008 Eclipse GS. I'm having trouble with my lock actuators. I have been unable to find a maintenance manual at the local parts stores. I've purchased the actuator motors to rebuild the actuator. However, I am having trouble removing the inner panel of the door. When I remove the...

Hey guys, On our ‘06 GS, we’re doing the front brakes over. On the backing plates (aka splash shields, dust shields, etc) there are the two main bolts that go through it (brake caliper bracket bolts). No problem there. But there is one small 10mm bolt as well, which of course immediate broke...

Hello! I scored a decent motor from a totalled 05 Outlander AWD and am wondering where to start with my build. So far I've torn it apart to check the condition of the internals: What should my next step be? My build is essentially going to be a stock build and having to smog it every couple...

Please help new to forum I have a 2008 eclipse with a 3.8 litter v6 trying to replace the converter against the fire wall ,I have got it loose but cannot for the life of me been able to remove it from car above or below have removed all bolts from. Engine mounts and tried lifting engine as much...