Search Results for ‘lower’

I have a 2008 eclipse with the 4cly engine. having what seemed at first to be a starter problem where it would try to turn over and sound like it was shorting out, no smoke or anything I could detect. wiggling the key did not really help. It got progressively worse and at one point now the air...

I fixed the play in my shifter completely. Managed to make a plastic spacer (43mm or 1 11/16 od, 37mm or 1 15/32 id, Width as desired) underneath the lower ball seat, to raise it a mm or so. and then dremel out the upper retainer for the pivot ball a mm as well. A clean up and regrease with...

I recently got an Endeavor plastic intake and its pretty impressive. It makes the 3.8 mivec intake look tiny. It has the same diameter runners as the mivec, but they are 3” longer. The plastic is smoother inside. The lower intake has a lot of potential also. The throttle bodies look very...

For those who have yet to suffer through this, a few tips I learned through my experience! – Earlier this year, we bought the car used, knowing it was from up north and was rusty underneath. The only real problem we’ve had so far was the fuel tank started leaking from the two vent lines on top...

What's up guys? As you can tell from my pics, I have an aftermarket Blackout-3 front bumper from AIT Racing (close up pic of bumper is attached). Unfortunately, I can't figure out a way to get my stock foglights mounted in it (trust me... I've tried everything lol). My foglight wiring/internals...

Just curious if anyone knew of a suitable replacement for the lower molding around the back of the eclipse glass. I've contacted several dealers and it seems the oem is no longer available from anywhere. After 12-something years the lower molding has turned into a u-shaped thing between the...

The P0102 code is the MAF circuit low input code. For me it threw a check engine light and the car wouldn't stay running unless I gave it gas. Ran super rough otherwise. The TCL light also comes on. I'm guessing anytime the car is running bad the TCL light probably comes on, because the 4G...

There's already been quite a few reviews of Stayer's tune, but here's another with additional details for those still on the fence or shopping for a reflash. As mentioned in another thread, I had been dealing with codes of late, having installed RRE headers a year ago. I was waiting to pass...

https://www.youtube.com/watch?v=t5-MWWJ0sx0 Hello everyone! Today we are here with a new video review on one of the most effective rotor-pad kit for your braking system - Power Stop Z23 Brake Kit. It includes ceramic pads and cross-drilled rotors, that offer better stopping power, longer life...

Didn't see a step by step so I thought I'd help out. I did not disconnect exhaust. But you may have to depending on your setup. Step 1 is get a jack with a piece of wood on it and support the transmission. Step 2 is remove the rear two bolts on the centermember. Step 3 is remove the...

After reading the manual and what I could find here, I've come to the conclusion that either i'm retarded or i'm missing something. But in the process I found it a whole lot easier to just remove the 6 bolts holding it down, push it up as far as it goes. than you can access the lower bolt on the...

Hi from Germany, can anybody measure the distance between the front upper and lower O2 sensor ! and if possible the rear too !? I have the obx long tube headers and i want to put the lower sensors back in place . Thanks for ur time. Greetz Markus

I soo need to lower Red October. Looks soo good. Now to put in the OT to get coilovers!! Sent from my VS995 using Tapatalk

Hello Club 4G, My current stereo seems to be broken as every 15 seconds it pauses the music and the little screen says "Phone", anyway I'm thinking I need a new stereo. If anyone has one laying around let me know. I am looking to purchase a 2010-2012 Eclipse OEM Radio Stereo with a 6 Disk CD...

Has any one used them. I really dont wanna chnage O2 sensors seeing that i think its my cat thats shot. I bot a set of them when i got my o2 sensor wrench. But bout some short ones cause there isnt much space on the lower sensors. I did not relize how long the end of the sensor was...... It...

Ok hello everyone, I'm sorry if I put this in the wrong place. But looking for some help and info. I have been looking to lower my 2012 spyder GT read the forums to look at the D2 coilover kits. the questions I'm having is: 1. what is the difference between D2 Racing®0"-2" x 0"-2" Circuit...

Alrighty, so i am having a hard time deciding whether i want to buy some coil overs or a carbon fiber hood. My thoughts on both for you to help me decide. I'm already sitting on tein s-tech springs soooo! If i buy a hood i will be able to vent all that excess heat out and get rid of some...

Well after 3.5 years of having my car I am finally making my car thread :pat: I bought my car back in 2014 with 71,xxx miles on it. I was never a big fan of the 4th gen but the moment I saw the facelifted 09 gt I was in love with it. Then I drove it and couldn't say no. (I had a 3rd gen that...

Hi All, Looking to replace the radiator on an 06 GS with manual trans and wanted to see if the procedure below sounds about right. EDITED to cover what actually was done now that job was completed.(may have missed something as doing from memory) Remove negative battery cable! Chock rear...