Search Results for ‘replace’

Does anyone have alink or know how to replace the speakers in the rear of a spyder :fever:

I just patched the two vapor return lines that seem to rust out under that heavy steel cover. ( got the p0442 and then the p0445 ) . I see you can order the entire filler tube component, is it hard to replace if I put the car up on ramps ? Can you get to the upper filler neck hose connections...

Is there any other way to connect an aftermarket stereo to the rockford system without having to buy that ridiculously expensive harness? The MITO-01? I had a MITO-01 in my vehicle, and my stereo got stolen out of my car in the middle of the night, and they just ripped it out of my dashboard...

Hey Everyone. Wanted everyone to know that Boosted Fab (Boostedfabrication.com) you can now order custom Poly Engine mounts to replace the Hydraulic mount for both GS and GT. As well as the Trans mounts for the GS and GT. I'm running them both along with the Energy suspension Bushings on...

I have a 2008 eclipse with the 4cly engine. having what seemed at first to be a starter problem where it would try to turn over and sound like it was shorting out, no smoke or anything I could detect. wiggling the key did not really help. It got progressively worse and at one point now the air...

Have a question about hid headlights being dim. I just acquired a 2009 Eclipse GT and the hid's seem dim. 1st step was to replace both headlight bulbs but thru a mixup only 1 hid bulb was replaced. The headlights seem a little brighter, but in general still seem dull/dim. The clear plastic of...

I want to upgrade to ES poly bushings, but ride quality and (mostly) cost are a concern. Is it possible to just replace the front control arm bushings and leave the backs OE rubber? Would that screw with handling/alignment? Has anyone done just front (or rear) only?

I've had RRE headers a few years now, and the car is running better than ever. At some point soon tho, I have to assume the 3rd cat will start to clog and fail due to age and especially since running headers. So 2 questions, 1) what are symptoms of a failing 3rd cat? 2) I'm inclined to...

So my cars been sounding weird I believe there is a hole in the front y-pipe. would it be best for me to replace just the y pipe or the whole front exhaust manifold and y pipe? Any suggestions or links would be helpful thank you

Whats the best way and cheapest way to replace engine or find a used one? I bent a rod in mine so its hard to decide. Shop wants to charge 7k for a whole new rebuilt engine that’s including labor and the new engine Sent from my iPhone using Tapatalk

just wondering if i should replace my cats or go for straight pipes any info dealing with this code 2007 eclipse 2.4 litre stock automatic transmission 198,000 kilometres

Hey guys, so I have no light on the digital dash clock, is this a fuse problem or a bulb problem I need to replace on the digital dash clock itself? Thanks.

Upon removing my cylinder head to replace a blown head gasket, I was cleaning up the mating surfaces on the head and as I spun it around to get to each surface, these fell out. Two of them fell onto the ground and I was not able to tell exactly where they came from and one was loose inside one...

07 eclipse gs got 76,700 mile replace timing belt couple hrs ago .. I start the car up and run it for about a block suddenly the engine cut off .. there good crank it just won’t start ..I need help ASAP .. thank in advance and sorry if it cost trouble ...thanks again

Trying to remove wheel hub and bearing to replace got all bolts out but hub is basically stuck I’ve tried penetrating oil and hammering to no luck what can I do to remove this without getting a shop to do it? Should I just keep hammering it it hasn’t even broke a crack in between the two pieces...

Flywheel Issues 2006 GT v6 MT Hi, I have a 2006 Eclipse GT 3.8L Manual Trans and have recently pulled the flywheel and was going to replace it when i noticed there were no shims. It had been burning up starters and this may be the reason from what i've read. One guy listed part #MD365781 and...

I am readying myself for the next order and have come to my next ?'s I'm planning on getting energy suspension motor mounts I see they have control arm bushings are they worth getting also I want to replace the ball joints what is everyone's opinion on these MEVOTECH Complete Arm w/ Ball Joint...

everything lines up for top dead center except the oil pump. is it possible it jumped a tooth on the oilpump? WIll that harm my engine? I will of course put the oil pump back in time when i replace the belt, just waiting on parts. Im just wondering if there is anything special i should know...