Hi y'all I noticed some oil leaking under my car. It not too bad but i think its transmission oil because its right next to the CV Drive Shaft axle. I noticed that there is a little clean cutout hole in the same spot underneath so its a factory cut, right? I also put in Redline trans gear fluid...
Transmission fluid Manual 09 GS
My local Mechanic put RedLine 75w-80 full synthetic gear oil when he replaced the clutch. a year later, I changed the CV axle shaft and lost a bit of trans fluid in the process so I decided to drain and refill myself. I went to O'Reilly's and they gave me a...
Thank god this site is here!
I'm a new owner of a 4g 2006 5-speed manual transmission Eclipse, but I am here with a couple of questions, one hard, one easy, or both hard?
anyhow,
Easy question: Does the 2006 5-speed tranny Eclipse have a Passenger CV Axle compatibility with any other car...
I'm about to pull the manual transmission out of the car to replace the input shaft bearing. I wasn't sure if I could do it on jack stands or if I needed to invest in some sort of lift.
So basically, how high does the car have to be to remove the transmission?
i apologize if this has been posted before i wasn't able to find anything in the other threads about the obx version one (ripp knockoffs) having clearance issues with the passenger side intermediate shaft. i know that there was someone who got them to work with a bit of modifications. if anyone...
I got a new cranks shaft position sensor, and now a month later it is throwing the code again, can someone help me figure out what the real issue is? Thank you
Sent from my SM-N950U using Tapatalk
2006 Mitsubishi Eclipse GS
I am trying to install the piggy back ECU, i am looking for someone that has done this before with success for the Eclipse, the kit was design for the ralliart, the ECU Pinouts are different. I found the Pinouts on the RRM site and was told the 4 and 6 are setup the...
Alright, so I've already timed my engine. For the guys that already know, my cars timing belt broke, I had replaced the head and everything but i'm not getting spark, I'm getting everything else but spark.
I have put the engine markings to what I assume is spec, as I've aligned all the marks...
So I've been busy this winter collecting parts for a drivetrain overhaul come spring. I've picked up a clutch, flywheel, LSD and some MT-90 fluid. What else do I need to know/do before handing it over to the shop? Would rather have all my bases covered and leave nothing up to chance before the...
I mistakenly posted this in the wrong forum so I'm posting it here now. I have an '06 GS with manual tranny and a short time ago, I started hearing a humming/grinding noise. It sounded and acted just like a wheel bearing. After doing the swerving test and jacking it up with both front wheels off...
I have an '06 GS manual trans. A short time ago, I started hearing what sounded like a bad wheel bearing. It acted like a bad passenger side wheel bearing (when swerving to the left it got a little louder, when swerving to the right it got a little quieter). So, I replaced the front passenger...
I recently acquired an eclipse gt 2006, came with a gearbox with Dog-leg pattern Does anyone know anything about this?,apparently it was automatic and converted to manual, the gearbox looks like the 6-speed, but only has 5 speeds, I need to change the input shaft bearing :(
hello, I've been trying to find a crankshaft for my 2006 Eclipse GT with a 3.8 L engine 6g75 motor. I haven't been able to find anything specifically for the eclipse but, I can go to a local junkyard and get one from another engine the only problem is they do not have the 06 eclipse in the...
how can to identify my 4g eclipse gt transmission, I recently acquired an eclipse, but it only has 5 speeds + reverse :pat:, it have a noise and I think it's input shaft bearing but first i have to know what tranmission i have, some body can help me im from mexico, sorry for my bad english
After about a year of on and off attempts to get one made by a shop for a reasonable price, here it is. Set me back $150, and the shop originally wanted $200 for one, but I got it knocked down a bit. To make more of them costed way too much. It was going to be $50 for each additional one. No...
So, I have a few problems with my driveline - I think.
2007 GS - 5MTX
1. My gears grind if I shift too quickly. There doesn't seem to be specific gears that do it, but I've noticed it on gears 2,3 and 5.
2. When I let off and reapply gas, there's a jerk each time. When I let off, there is a...
Hi peeps, we've done the 'balance shaft elimination' on a 4G54/G54B (2,6 Lt Astron 1 motor - in a Mitsubishi Sigma). We've fitted the eliminator kit on the motor, starts & everything, BUT, No oil pressure !! If we manually prime the oil pump (via the oil pressure sensor outlet on the side of the...