Just swap a GT TB to my GS, ECU reset, runs fine, no screaming noises, but the RPM drops really slow when below 2000rpm, also the RPM jumps a lot from 1000rpm -1500rpm when stopped.
Should I get a new gasket?
Any help is appreciated.
Hello, I am Ian from the USA. this is my 4g, I also own a 3kgt that i am currently restoring. lowered on eBay coil overs (temporary. Looking into Further options for autox) Catback exhaust, cold air intake (heat wrapped), throttle body coolant bypass, fog light delete( for summer only), and a...
Hey new comer here, i just got an eclipse 07 for free, and its basically mint too at 57k miles, a good deal in my opinion, and i just wanted to know if i can get this little slug to 200hp, or atleast like 180whp or something because imo its pretty slow, bordering prius power at like 130whp, but...
I have a 2009 with the 2.4L that after pulling into the driveway the other night the check engine light came on and it started idling rough as hell. I shut it off and restarted it. It started back up but ran rough as hell, tach was at around 1000rpms but it felt like 150-200, it would finally...
So here's the lowdown:
I have changed the camshaft sensor/crankshaft sensor, thermostat, coils, spark plugs, coolant, cleaned MAF, cleaned throttle body, put new clutch and throwout bearing. Oil is topped off good and no real leaks.
The car drives real good for about fifteen minutes and then...
Alrighty, So as I have postponed or rejected the turbo idea due to the fact that I want this car to remain as a fun daily and don't want to really risk it's functionality. I am back to bolt ons. I know the headers are the top pic for the 6g75 but I have been doing some thinking.
I was thinking...
Hopefully someone has an answer for my really obscure problem I've been troubleshooting.
So I just did an engine swap, and now when I turn the key to "On", power is alright. The ECU is getting 12v, ECU grounds are good, body grounds are good, trans ground is good.
However, when I turn it to...
It's pretty remarkable what an ECU tune can do. I've installed a cold air intake, gutted all 3 cats, installed a high-performance muffler, throttle body bypass, etc, etc. I've probably spent 30 hours crawling around under the car, replacing this, adjusting that...and then Stas (Stayer) comes...
Hey folks,
Thought about buying an oem TB from someone parting out then working with Proflow on reboring it but would much rather just buy a used Proflow TB if anyone has it.
If anyone is willing to get rid of their 67mm let me know and we'll work out a deal :)
Thank you
Anyone elses throttle body make a buzzing sound when key is in the on posistion?
Upload speed is really slow right now but im uploading a video ill post when its done.
Sent from my VS995 using Tapatalk
This is kinda long, but please take the time to read it because I would really appreciate it. So about 2-3 weeks ago, I thought I hydrolocked my engine because I accidentally drove through a deep puddle after rain, and as soon as I drove through it, my engine seized and refused to turn over. All...
2006 GS 2.4 coupe
Recently the car broke the teeth off the timing belt, took a bit to figure out that was the issue but first replaced the fuel pump, then noted the cam was not spinning when it still wouldn't start.
Replaced the timing belt and water pump
Car ran fine for a couple weeks, then...
So, I have a Crank no start issue but everything is a okay (I've checked everything.) I've tried Starter fluid but I couldn't get the throttle body to open up so I basically sprayed it in the air tube, behind the air sensor so as not to mess with that. I held down the gas pedal but to no avail I...
Hey guys, haven't been on this site in a while, but after asking around on the threads, I was recommended an Injen CAI for my 2006 Eclipse GT. You hear different claims, and people stating that they did get those claims or did not, but I am happy to report that the Injen CAI I just installed in...
Warning: Do NOT do this mod. My Engine Coolant Temperature Sensor blew and my car went into limp mode at extremely high temps. and would not start. I almost had to have it towed but luckily there was an auto store nearby where I was able to plant the car under a tree. I had to pay $170 for a...
Hey all,
I'm thinking about ordering some 0.125" teflon sheet to make some phenolic spacers for my intake manifold and throttle body. I wanted to see if anyone else has done this/used the pre-made ones because I'm curious if its necessary to use a regular gasket on both sides such a spacer or...